Outdoor Lighting Installation for Livermore Homes: Landscape and Line-Voltage Systems

Licensed Golden Electrical electrician

Outdoor lighting installation is two different trades wearing one name. One runs 120 volts to fixtures on the building, wired like any other branch circuit. The other runs 12 volts from a transformer out into the yard under almost none of the same rules. Trenching depth, controls and the way each fails are all different.

Short Answer

Line-voltage outdoor lighting is a branch circuit, and in general locations the wire needs 24 inches of cover direct buried, 18 inches in PVC, or 12 inches if it is a residential circuit at 120 volts or less with GFCI protection and a 20 amp maximum breaker. Low-voltage landscape lighting at 30 volts or less needs only 6 inches with the same GFCI and 20 amp conditions, which is why it is a far smaller job. Under Title 24, outdoor lighting attached to the house must be high efficacy and controlled by a manual switch plus a photocell and motion sensor, a photocell and time switch, or an astronomical time clock. Voltage drop, not failure of the fixtures, is what kills most low-voltage systems.

Two Different Systems, Two Different Jobs

 Line-voltage (120V)Low-voltage (12–15V)
Typical fixturesSoffit and eave downlights, wall packs, security floods, garage and porch fixturesPath lights, uplights, step lights, well lights
How it is wiredA branch circuit — conduit or direct burial cable at code depthA transformer steps 120V down, then cable runs out to the fixtures
Permit pathSame permit and inspection as any other circuitLighter beyond the transformer, but its supply circuit is line-voltage work
StrengthsBrighter output, longer runs, no transformerShallower burial, less trenching, fixtures can be moved later without rewiring

Most houses end up with both. Building-mounted lighting is line-voltage because it needs the output and the position is permanent. The yard is low-voltage because the burial requirement is a quarter of the depth and layouts change as planting matures.

Home exterior with path lighting along the driveway and planting beds in Livermore, CA
Building-mounted lighting is line-voltage. The path and bed lighting in the yard is low-voltage, and buries at a quarter of the depth.

Outdoor Lighting Installation: How the Work Runs

  • 1. Load and circuit assessment. Whether an existing exterior circuit can carry the addition or a new one is needed from the panel. Older Livermore homes with full panels hit a capacity question before a lighting question.
  • 2. Layout. Fixture positions set against what they are lighting, not spaced evenly. Path lights placed to graze the walking surface, uplights set back to wash a tree rather than spotlight the trunk, downlights located so the source is out of anyone’s eye line.
  • 3. Transformer siting, for low-voltage. Near the supply circuit, within reach of the runs it feeds, accessible for service. Transformer position determines run lengths, which determines whether the far fixtures work properly.
  • 4. Trenching and routing. Depth set by method and circuit type, covered below. Routing has to avoid irrigation lines, which on a Livermore lot usually sit shallower than the electrical.
  • 5. Fixtures, connections and controls. Fixtures set, connections made with listed waterproof methods, control devices installed.
  • 6. Testing at night. The only time the layout can be judged. Aim, glare and the dark gaps between fixtures are invisible in daylight, and so is a fixture running dim at the end of a long run.

How Deep the Wire Has to Go

Minimum cover comes from Table 300.5 and depends on the wiring method and the circuit, not on preference. In general locations:

Wiring method or circuitMinimum cover
Direct burial cable24 inches
PVC conduit listed for direct burial18 inches
Rigid metal conduit or IMC6 inches
Residential branch circuit, 120V or less, GFCI protected, 20A max12 inches
Irrigation and landscape lighting, 30V or less, GFCI protected, 20A max6 inches

The 6 inch allowance is why low-voltage landscape lighting is a fraction of the labor, and it is not granted by low voltage alone: the circuit has to be at or under 30 volts, GFCI protected, and on a 20 amp maximum breaker. Miss a condition and the shallower depth does not apply.

Two Situations Change the Numbers

Under a driveway serving a one- or two-family dwelling, landscape lighting depth goes from 6 inches to 18. Under a public street, road or alley, everything goes to 24 regardless of method. A run crossing a driveway is a different job from the same run across a lawn. Confirm depths against the California Electrical Code edition in force.

What Title 24 Requires of the Controls

Outdoor lighting is not exempt from the energy code, and the requirement is about controls rather than the fixture alone.

Lighting attached to the residence, or another building on the same lot, must be high efficacy and controlled by a manual on and off switch plus one of three options: a photocell and motion sensor, a photocell and automatic time switch, or an astronomical time clock.

Read that as the code ruling out a plain switch. Something has to turn the lighting off without a person deciding to: daylight, time, or absence of motion.

So controls belong in the design rather than added at the end. A motion sensor in the wrong position triggers on the sidewalk, and a time clock is only useful if it is reachable. Where a project is already getting smart home wiring, the requirement is easier to satisfy well. Because published summaries of the energy code vary, confirm the control requirement against the adopted code before specifying.

Voltage Drop Is the Usual Failure

Low-voltage systems rarely fail because a fixture broke. They fail because the last fixtures on a run never got enough voltage to begin with.

At 12 volts the margin is small, so resistance over distance matters in a way it does not at 120 volts. A long run on undersized cable delivers noticeably less voltage at the end, and the symptom is fixtures dimmer and warmer in color the further out they sit.

Three things prevent it: cable sized for the run length rather than the fixture count, runs kept short through transformer siting, and a transformer with headroom above the connected load rather than sized exactly to it, since a system at capacity has nothing left when fixtures are added.

The fixtures will light on undersized cable. They just will not light evenly, and the cause is buried in the yard.

Licensed electrician installing exterior lighting at a Livermore, CA home
A layout can only be judged after dark — glare, aim and the dim end of a long run are all invisible in daylight.

Fixtures Have to Be Listed for Where They Sit

Exterior fixtures carry a location listing, and the distinction is not cosmetic.

Wet location listing is required anywhere a fixture meets direct weather: in the open, on an unprotected wall, in the ground, anywhere rain or sprinkler spray reaches. Damp location listing covers positions protected from direct water but still outdoors, such as a recessed fixture in a covered soffit or under a deep eave.

A damp-rated fixture in a wet location is a premature failure. In-grade and well lights sit in the hardest position of all, since they can be submerged after irrigation or heavy rain. Outdoor receptacles serving any of this need GFCI protection, a separate requirement from the lighting.

Key Takeaways

  • Line-voltage exterior lighting is a branch circuit. Low-voltage landscape lighting runs from a transformer under different rules.
  • General burial depths: 24 inches direct buried, 18 in PVC, 6 in rigid metal conduit, 12 for a GFCI-protected residential circuit on a 20 amp maximum breaker.
  • Landscape lighting gets 6 inches only if the circuit is 30 volts or less, GFCI protected and on a 20 amp maximum breaker.
  • Under a dwelling driveway, landscape lighting depth rises from 6 inches to 18. Under a public street, everything goes to 24.
  • Title 24 requires outdoor lighting attached to the house to be high efficacy with a manual switch plus a photocell and motion sensor, a photocell and time switch, or an astronomical time clock.
  • A plain wall switch alone does not satisfy the control requirement.
  • Voltage drop, not fixture failure, degrades most low-voltage systems. Cable size and run length decide it.
  • Fixtures need wet location listing where exposed to weather, damp location listing under cover. In-grade fixtures take the harshest position.

Frequently Asked Questions

Do I need a permit for outdoor lighting?

Adding a new circuit or running new wiring generally requires one, while replacing an existing fixture generally does not. Low-voltage work beyond the transformer is lighter, but the transformer’s supply circuit is line-voltage work. Local administration varies, so confirm with the Livermore Building Division, and note that permitted work verifies depth and control compliance rather than taking them on trust.

Is low-voltage or line-voltage better for a yard?

They do different jobs. Low-voltage suits path, garden and accent lighting, buries at 6 inches under the right conditions, and lets fixtures be relocated as planting changes. Line-voltage suits building-mounted lighting and security floods where output matters and the position is permanent.

Why are the lights at the end of my run dimmer?

Voltage drop, almost always. On a 12 volt system a long run on undersized cable delivers less voltage at the far end, and those fixtures run dim and shift warmer in color. The fix is cable sized for the run, a better-placed transformer, or splitting the load across more runs, not replacing the fixtures.

Can I just put outdoor lights on a regular switch?

Not on their own, for lighting attached to the house. The energy code requires a manual switch plus an automatic control: a photocell paired with a motion sensor or a time switch, or an astronomical time clock. Something has to shut the lighting off without a person deciding to, which is why the control gets specified alongside the fixtures.

How deep do landscape lighting wires need to be buried?

Six inches in general locations, provided the circuit is 30 volts or less, GFCI protected and on a 20 amp maximum breaker. All three conditions have to hold. Crossing a driveway raises it to 18 inches, and crossing a public street to 24. Confirm against the adopted California Electrical Code edition before trenching.

Planning Outdoor Lighting Installation

Good outdoor lighting installation is decided before anything is buried. Which system suits which part of the property, how deep each run goes, what control satisfies the energy code, and whether the cable is sized for the distance it covers. All four are cheap at layout and expensive once the trench is closed.

Indoors, the same compliance questions apply differently to recessed lighting.

Planning Exterior or Landscape Lighting?

Golden Electrical handles exterior and landscape lighting as part of residential electrical work in Livermore, Pleasanton, Dublin and San Ramon, including the circuit and panel side when a yard needs more capacity than the existing wiring provides, plus commercial exterior lighting. Get in touch with a rough layout, since run lengths and driveway crossings decide most of the scope.

Get a Lighting Quote See All Services